ass日本风韵熟妇pics男人扒开女人屁屁桶到爽|扒开胸露出奶头亲吻视频|邻居少妇的诱惑|人人妻在线播放|日日摸夜夜摸狠狠摸婷婷|制服 丝袜 人妻|激情熟妇中文字幕|看黄色欧美特一级|日本av人妻系列|高潮对白av,丰满岳妇乱熟妇之荡,日本丰满熟妇乱又伦,日韩欧美一区二区三区在线

甘蔗收獲機入土切割深度控制系統研究
CSTR:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

國家自然科學基金項目(32071916)和廣西科技重大專項(桂科AA22117005)


Under-the-ground Basecutting Control System of Sugarcane Harvester
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 圖/表
  • |
  • 訪問統計
  • |
  • 參考文獻
  • |
  • 相似文獻
  • |
  • 引證文獻
  • |
  • 資源附件
  • |
  • 文章評論
    摘要:

    甘蔗入土切割可以有效降低根切破頭率,由于西南丘陵山地蔗田凹凸不平,,現有甘蔗收獲機難以控制刀盤進行入土切割作業,,導致甘蔗機收產生大量根切破頭。針對以上問題,,本文利用自行研制的甘蔗入土切割試驗臺,,基于角度傳感器,、切割壓力傳感器,設計了一種多傳感器數據融合的入土切割控制系統,開發了基于PID算法的刀盤高度控制策略,,運用Matlab/Simulink構建系統仿真模型,。仿真結果表明,入土切割控制系統的穩定時間為0.67s,,超調量為8.6%,。為驗證入土切割控制系統的作業效果,以前進速度,、地面波長和地面振幅為試驗因素模擬蔗田路面,,進行了臺架試驗。試驗結果表明,,當前進速度為1km/h,、地面波長為1m、地面振幅為4cm時,,最小平均入土切割深度誤差為3.26mm,。當前進速度為3km/h、地面波長為1m,、地面振幅為12cm時,,最大平均入土切割深度誤差為8.87mm,刀盤可以保持入土切割,。研究可為入土切割控制系統的開發提供數據支撐和理論依據,。

    Abstract:

    Sugarcane is a perennial crop, and good cutting quality can promote the growth and germination of sugarcane in the coming year. A large number of experimental studies have shown that under-the-ground basecutting can effectively reduce the stubble damage. Due to the unevenness of sugarcane fields in the hilly and mountainous areas of southwestern China, it is difficult for sugarcane harvesters to keep under-the-ground basecutting, resulting in a large amount of stubble damage. Therefore, based on angle sensors and cutting pressure sensors, the test bench was developed to design a multi-sensor data fusion control system. The basecutter height control strategy based on PID algorithm was developed, and the simulation model of the system was built by Matlab/Simulink. The simulation results showed that the stability time of the system was 0.67s, and the overshoot was 8.6%. To verify the performance of the control system, the bench test was carried out to simulate the sugarcane ground surface with forward speed, ground wavelength and ground amplitude as test factors.The experimental results showed that the minimum average cutting depth error was 3.26mm when the forward speed was 1km/h, the ground wavelength was 1m and the ground amplitude was 4cm. When the forward speed was 3km/h, the ground wavelength was 1m, and the ground amplitude was 12cm, the maximum average cutting depth error was 8.87mm, and the basecutter can keep under-the-ground basecutting. The research provided data support and theoretical basis for the development of the control system for under-the-ground basecutting.

    參考文獻
    相似文獻
    引證文獻
引用本文

丁征亮,馬少春,霍鵬,李偉慶,錢君,周保成.甘蔗收獲機入土切割深度控制系統研究[J].農業機械學報,2023,54(s2):121-127. DING Zhengliang, MA Shaochun, HUO Peng, LI Weiqing, QIAN Jun, ZHOU Baocheng. Under-the-ground Basecutting Control System of Sugarcane Harvester[J]. Transactions of the Chinese Society for Agricultural Machinery,2023,54(s2):121-127.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2023-06-11
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2023-08-01
  • 出版日期:
文章二維碼