ass日本风韵熟妇pics男人扒开女人屁屁桶到爽|扒开胸露出奶头亲吻视频|邻居少妇的诱惑|人人妻在线播放|日日摸夜夜摸狠狠摸婷婷|制服 丝袜 人妻|激情熟妇中文字幕|看黄色欧美特一级|日本av人妻系列|高潮对白av,丰满岳妇乱熟妇之荡,日本丰满熟妇乱又伦,日韩欧美一区二区三区在线

基于激光雷達的稻麥?zhǔn)斋@邊界檢測與自動對齊系統研究
CSTR:
作者:
作者單位:

作者簡介:

通訊作者:

中圖分類號:

基金項目:

科技創新2030-新一代人工智能項目(2021ZD0110902)和國家自然科學基金項目(32171907)


Rice and Wheat Harvesting Boundary Detection and Automatic Alignment System Based on LiDAR
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 圖/表
  • |
  • 訪問統計
  • |
  • 參考文獻
  • |
  • 相似文獻
  • |
  • 引證文獻
  • |
  • 資源附件
  • |
  • 文章評論
    摘要:

    針對稻麥?zhǔn)斋@無人作業的需求,提出了一種使用激光雷達檢測稻麥?zhǔn)斋@邊界的算法,,并連接無人控制系統實現收獲邊界的自動對齊,。該算法首先對采集的收獲輪廓點云劃定感興趣角度范圍,根據雷達的安裝高度和位置將測量數據由極坐標轉換為三維直角坐標,,融合陀螺儀測量的激光雷達安裝姿態數據對測量點云進行校正,;通過中值濾波和Z向閾值濾波將點云中的噪點和非稻麥輪廓點濾除;對比了K-means聚類和Z向中心差分法檢測稻麥?zhǔn)斋@邊界的精度,,并進行了誤差分析,;開發了感知系統并制定了感知與控制的CAN通信協議,采用預瞄點追蹤方法對實時檢測的邊界點進行對齊控制,;分析研究了稻麥?zhǔn)斋@邊界自動對齊精度檢測方法,。2022年6月在北京小湯山國家精準農業示范基地進行了收獲邊界檢測與自動對齊控制系統試驗,分別采用數據標注和GPS打點的方式進行了數據采集與分析,,試驗結果表明,,基于K-means聚類的收獲邊界檢測橫向偏差平均值為22.24cm,基于Z向中心差分法的收獲邊界檢測橫向偏差平均值為1.48cm,,Z向中心差分法的收獲邊界檢測優于基于K-means聚類的檢測方法,,故采用Z向中心差分法進行自動對齊控制試驗,整體控制系統自動對齊橫向偏差平均值為9.18cm,,標準差為2.48cm,,該系統可用于稻麥?zhǔn)斋@無人作業。

    Abstract:

    To meet the demand for unmanned operations in rice and wheat harvesting, an algorithm using LiDAR to detect the rice and wheat harvest boundary was proposed, and the automatic alignment of the harvest boundary was realized by connecting the unmanned control system. Firstly, the algorithm delimited the angle range of interest for the collected harvesting outline point cloud, converted the measured data from polar coordinates to three-dimensional rectangular coordinates according to the installation height and position of the LiDAR, and corrected the measured point cloud by fusing the LiDAR attitude measured by the gyroscope. The noise and non-crop contour points in the point cloud were filtered by median filtering and Z-direction threshold filtering. The accuracy of K-means clustering and Z-direction central difference method for detecting harvest boundary was compared, and the error analysis was carried out. The sensing system was developed and the CAN communication protocol of sensing and control was established. Point tracking strategy was adopted to automatically control the boundary points detected in real time. The automatic alignment accuracy detection method of rice and wheat harvest boundary was analyzed and studied. In June 2022, the experiment of harvesting boundary detection and automatic alignment control system was carried out at Xiaotangshan National Precision Agriculture Demonstration Base in Beijing. The data were collected and analyzed by using data annotation and GPS pointing respectively. The experiment showed that the average horizontal error of harvesting boundary detection based on K-means clustering was 22.24cm, the average horizontal error of the Z-direction central difference method was 1.48cm, and the Z-direction central difference method was superior to the K-means clustering method. Therefore, the Z-direction central difference method was used for automatic alignment control experiment. The average value of lateral deviation of automatic alignment control system was 9.18cm, and the standard deviation was 2.48cm. The system can be used for unmanned rice and wheat harvesting.

    參考文獻
    相似文獻
    引證文獻
引用本文

尚業華,王昊,孟志軍,尹彥鑫,肖躍進,宋正河.基于激光雷達的稻麥?zhǔn)斋@邊界檢測與自動對齊系統研究[J].農業機械學報,2023,54(5):19-28,,46. SHANG Yehua, WANG Hao, MENG Zhijun, YIN Yanxin, XIAO Yuejin, SONG Zhenghe. Rice and Wheat Harvesting Boundary Detection and Automatic Alignment System Based on LiDAR[J]. Transactions of the Chinese Society for Agricultural Machinery,2023,54(5):19-28,,46.

復制
分享
文章指標
  • 點擊次數:
  • 下載次數:
  • HTML閱讀次數:
  • 引用次數:
歷史
  • 收稿日期:2022-12-30
  • 最后修改日期:
  • 錄用日期:
  • 在線發布日期: 2023-05-10
  • 出版日期:
文章二維碼